| SIMATIC DP, ELECTRONIC MODULE ET 200SP, F-AI 4xI(0)4..20mA HF FAILSAFE ANALOG INPUTS up to PL E (ISO 13849) up to SIL 3 (IEC 61508) |
| General information |
| Product type designation | F-AI 4xI 0(4) ... 20 mA 2/4-wire HF |
| Firmware version | |
| FW update possible | Yes |
| usable BaseUnits | BU type A0, A1 |
| Color code for module-specific color identification plate | CC00 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | V15 with HSP 203 |
| CiR – Configuration in RUN |
| Reparameterization possible in RUN | No |
| Calibration possible in RUN | No |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| Current consumption (rated value) | 0.38 A |
| Current consumption, max. | 0.4 A |
| Encoder supply |
| 24 V encoder supply |
| 24 V | Yes; min. L+ (-1.5 V) |
| Short-circuit protection | Yes |
| Output current, max. | 300 mA; total current of all encoders/channels |
| Power |
| Power available from the backplane bus | 70 mW |
| Power loss |
| Power loss, typ. | 2 W |
| Address area |
| Address space per module |
| Inputs | 14 byte; S7-300/400F CPU, 13 byte |
| Outputs | 5 byte; S7-300/400F CPU, 4 byte |
| Hardware configuration |
| Automatic encoding | |
| Electronic coding element type F | Yes |
| Analog inputs |
| Number of analog inputs | 4 |
| For current measurement | 4 |
| permissible input current for current input (destruction limit), max. | 35 mA |
| Input ranges (rated values), currents |
| 0 to 20 mA | Yes |
| Input resistance (0 to 20 mA) | 125 Ω |
| 4 mA to 20 mA | Yes |
| Input resistance (4 mA to 20 mA) | 125 Ω |
| Cable length |
| shielded, max. | 1 000 m |
| Analog value generation for the inputs |
| Measurement principle | Sigma Delta |
| Integration and conversion time/resolution per channel |
| Resolution with overrange (bit including sign), max. | 16 bit |
| Integration time, parameterizable | Yes |
| Integration time (ms) | 20 / 16,667 |
| Interference voltage suppression for interference frequency f1 in Hz | 50 / 60 Hz |
| Smoothing of measured values |
| Number of smoothing levels | 7 |
| parameterizable | Yes |
| Step: None | Yes; 1x conversion cycle time |
| Step: low | Yes; 2x / 4x conversion cycle time |
| Step: Medium | Yes; 8x / 16x conversion cycle time |
| Step: High | Yes; 32x / 64x conversion cycle time |
| Encoder |
| Connection of signal encoders |
| for current measurement as 2-wire transducer | Yes |
| — Burden of 2-wire transmitter, max. | 650 Ω |
| for current measurement as 4-wire transducer | Yes |
| Errors/accuracies |
| Linearity error (relative to input range), (+/-) | 0.1 % |
| Temperature error (relative to input range), (+/-) | 0.023 %/K |
| Repeat accuracy in steady state at 25 °C (relative to input range), (+/-) | 0.1 % |
| Operational error limit in overall temperature range |
| Current, relative to input range, (+/-) | 2 % |
| Basic error limit (operational limit at 25 °C) |
| Current, relative to input range, (+/-) | 0.1 % |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency |
| Series mode interference (peak value of interference < rated value of input range), min. | 40 dB |
| Common mode interference, min. | 70 dB |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes, "Alarms/diagnostic messages" section in the manual |
| Alarms |
| Diagnostic alarm | Yes |
| Limit value alarm | Yes |
| Diagnostic messages |
| Monitoring the supply voltage | Yes |
| Wire-break | Yes; Measuring range 4 to 20 mA only |
| Short-circuit | Yes |
| Diagnostics indication LED |
| RUN LED | Yes; Green LED |
| ERROR LED | Yes; Red LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for channel diagnostics | Yes; Red LED |
| for module diagnostics | Yes; Green/red LED |
| Potential separation |
| Potential separation channels |
| between the channels | No |
| between the channels and backplane bus | Yes |
| between the channels and the power supply of the electronics | Yes |
| Permissible potential difference |
| between the inputs (UCM) | 10 Vpp |
| Isolation |
| Isolation tested with | 707 V DC (type test) |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | 0 °C |
| horizontal installation, max. | 60 °C |
| vertical installation, min. | 0 °C |
| vertical installation, max. | 50 °C |
| Dimensions |
| Width | 15 mm |
| Height | 73 mm |
| Depth | 58 mm |
| Weights |
| Weight, approx. | 48 g |
| last modified: | 03/13/2019 |
