| *** SPARE PART*** SIMATIC DP, ELECTRONIC MODULE ANALOG, FOR ET 200B, W=160MM, 4AI 0(4)...20MA; +/- 10V, FAST CONVERSION, 12 BITS |
| General information |
| Usable terminal block | TB8 |
| Supply voltage |
| Rated value (DC) | 24 V; Value at t < 0.5 s: 35 V |
| permissible range, lower limit (DC) | 18.5 V |
| permissible range, upper limit (DC) | 30.2 V |
| Input current |
| Current consumption, typ. | 70 mA; Logic |
| Power loss |
| Power loss, typ. | 1.8 W |
| Analog inputs |
| Number of analog inputs | 4 |
| permissible input voltage for voltage input (destruction limit), max. | 30 V; ±30 V (static) or ±75 V (pulse for max. 1 ms and mark to space ratio 1:20) |
| permissible input current for current input (destruction limit), max. | 24 mA |
| Cycle time (all channels) max. | 5 ms |
| Input ranges |
| Voltage | Yes |
| Current | Yes |
| Input ranges (rated values), voltages |
| -1.25 V to +1.25 V | Yes |
| Input resistance (-1.25 V to +1.25 V) | 100 kΩ |
| -10 V to +10 V | Yes |
| Input resistance (-10 V to +10 V) | 100 kΩ |
| -2.5 V to +2.5 V | Yes |
| Input resistance (-2.5 V to +2.5 V) | 100 kΩ |
| -5 V to +5 V | Yes |
| Input resistance (-5 V to +5 V) | 100 kΩ |
| Input ranges (rated values), currents |
| 0 to 20 mA | Yes |
| Input resistance (0 to 20 mA) | 125 Ω |
| -20 mA to +20 mA | Yes |
| Input resistance (-20 mA to +20 mA) | 125 Ω |
| 4 mA to 20 mA | Yes |
| Input resistance (4 mA to 20 mA) | 125 Ω |
| Cable length |
| shielded, max. | 100 m |
| Analog value generation for the inputs |
| Measurement principle | successive approximation |
| Integration and conversion time/resolution per channel |
| Resolution with overrange (bit including sign), max. | 12 bit; Two's complement |
| Integration time (ms) | 0.1 ms / channel |
| Encoder |
| Connection of signal encoders |
| for voltage measurement | Yes |
| for voltage measurement as 2-wire transducer | Yes |
| for current measurement as 2-wire transducer | Yes |
| for current measurement as 4-wire transducer | Yes |
| Errors/accuracies |
| Operational error limit in overall temperature range |
| Voltage, relative to input range, (+/-) | 32 %; 0 to 60°C |
| Current, relative to input range, (+/-) | 41 %; 0 to 60°C |
| Basic error limit (operational limit at 25 °C) |
| Voltage, relative to input range, (+/-) | 0.15 % |
| Current, relative to input range, (+/-) | 0.2 % |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency |
| Common mode interference, min. | 70 dB; Upp < 1 V |
| Interfaces |
| PROFIBUS DP |
| Transmission rate, max. | 12 Mbit/s |
| Protocols |
| Bus protocol/transmission protocol | PROFIBUS DP |
| Interrupts/diagnostics/status information |
| Alarms |
| Diagnostic alarm | Yes; Parameterizable |
| Limit value alarm | Yes; Parameterizable, channels 0 and 2 |
| Diagnostic messages |
| Overrange | Yes; Rated range |
| Wire-break in signal transmitter cable | Yes; Measuring range 4 to 20 mA only |
| Diagnostics indication LED |
| RUN LED | Yes |
| Bus fault BF (red) | Yes |
| Potential separation |
| between electronic block and PROFIBUS DP | Yes |
| Potential separation analog inputs |
| Potential separation analog inputs | No |
| Permissible potential difference |
| between the inputs (UCM) | max. ±10 V |
| Between the inputs and MANA (UCM) | max. ±1 V |
| Degree and class of protection |
| Degree of protection acc. to EN 60529 | IP20 |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | 0 °C |
| horizontal installation, max. | 60 °C; 41 °C for other mountings |
| Air pressure acc. to IEC 60068-2-13 |
| permissible range, lower limit | 795 hPa |
| permissible range, upper limit | 1 080 hPa |
| Relative humidity |
| Operation, min. | 15 % |
| Operation, max. | 95 %; RH class 2 in accordance with IEC 1131-2 |
| Vibrations |
| Operation, tested according to IEC 60068-2-6 | Yes; IEC 68, Part 2-6; 10 to 57 Hz; (constant amplitude 0.075 mm); 57 to 150 Hz; (constant acceleration 1 g) |
| Shock testing |
| tested according to IEC 60068-2-27 | Yes; IEC 68, Part 2-27; half-sine, 15 g, 11 ms |
| Connection method |
| Design of electrical connection for the inputs and outputs | Screw-type and spring-loaded terminals, permanent wiring; 3 and 4-wire connection |
| Dimensions |
| Width | 160 mm; EB and TB |
| Height | 130 mm; EB and TB |
| Depth | 60 mm; EB and TB |
| Weights |
| Weight, approx. | 550 g; EB and TB |
| last modified: | 03/13/2019 |
