| *** Spare part *** SIMATIC ET 200SP, digital input module, DI 4x 120..230 V AC Standard suitable for BU type B1, color code 41 module diagnostics |
| General information |
| Product type designation | DI 4x120 … 230 V AC ST |
| Firmware version | V1.0 |
| FW update possible | Yes |
| usable BaseUnits | BU type B1 |
| Color code for module-specific color identification plate | CC41 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | V13 / V13 |
| STEP 7 configurable/integrated as of version | V5.5 SP3 / - |
| PROFIBUS as of GSD version/GSD revision | GSD Revision 5 |
| PROFINET as of GSD version/GSD revision | GSDML V2.3 |
| Operating mode |
| DI | Yes |
| Counter | No |
| Oversampling | No |
| MSI | No |
| Supply voltage |
| Rated value (AC) | 230 V |
| Reverse polarity protection | No |
| Input current |
| Current consumption (rated value) | 10 mA |
| Encoder supply |
| Number of outputs | 4 |
| Short-circuit protection | No; when using BU type B1, a fuse with 10 A tripping current must be provided |
| Output current |
| up to 60 °C, max. | 10 A |
| 24 V encoder supply |
| 24 V | No |
| Short-circuit protection | No |
| Power loss |
| Power loss, typ. | 1 W; Active power, load voltage 230 V, all inputs connected with 230 V, 50 Hz |
| Address area |
| Address space per module |
| Address space per module, max. | 1 byte; + 1 byte for QI information |
| Inputs | 1 byte |
| Hardware configuration |
| Selection of BaseUnit for connection variants |
| 1-wire connection | BU type B1 |
| 2-wire connection | BU type B1 |
| 3-wire connection | BU type B1 |
| 4-wire connection | BU type B1 + external terminals |
| Digital inputs |
| Number of digital inputs | 4 |
| Source/sink input | No |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Pulse extension | No |
| Input voltage |
| Rated value (AC) | 230 V |
| for signal "0" | 0V AC to 40V AC |
| for signal "1" | 74 V AC to 264 V AC |
| Input current |
| for signal "1", typ. | 10.8 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — parameterizable | No |
| — at "0" to "1", min. | 1.5 ms |
| — at "0" to "1", max. | 4 ms |
| — at "1" to "0", min. | 10 ms |
| — at "1" to "0", max. | 10 ms |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Alarms |
| Diagnostic alarm | No |
| Hardware interrupt | No |
| Diagnostic messages |
| Wire-break | No |
| Short-circuit | No |
| Group error | Yes |
| Diagnostics indication LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for channel diagnostics | No |
| for module diagnostics | Yes; green/red DIAG LED |
| Potential separation |
| Potential separation channels |
| between the channels | No |
| between the channels and backplane bus | Yes |
| between the channels and the power supply of the electronics | No |
| Isolation |
| Isolation tested with | 2 545 V DC/2 s (routine test) |
| Standards, approvals, certificates |
| Suitable for safety functions | No |
| Dimensions |
| Width | 20 mm |
| Height | 73 mm |
| Depth | 58 mm |
| Weights |
| Weight, approx. | 36 g |
| last modified: | 03/29/2019 |
