| SITOP PSU8200 24 V/40 A |
| SITOP PSU8200 24 V/40 A Stabilized power supply input: 120/230 V AC, output: 24 V DC/40 A |
| Input |
| Input | 1-phase AC |
| Note | Automatic selection; startup starting from Ue ≥ 90/180 V |
| Supply voltage | |
| 1 at AC Rated value | 120 V |
| 2 at AC Rated value | 230 V |
| Input voltage | |
| 1 at AC | 85 ... 132 V |
| 2 at AC | 170 ... 264 V |
| Wide-range input | No |
| Mains buffering at Iout rated, min. | 25 ms; at Vin = 230 V |
| Rated line frequency 1 | 50 Hz |
| Rated line frequency 2 | 60 Hz |
| Rated line range | 45 ... 65 Hz |
| Input current | |
| at rated input voltage 120 V | 15 A |
| at rated input voltage 230 V | 9 A |
| Switch-on current limiting (+25 °C), max. | 60 A |
| I²t, max. | 8 A²·s |
| Built-in incoming fuse | Yes |
| Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker at 1-phase operation: 16 A characteristic C; required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2421-4BA10 (120 V) or 3RV2411-1JA10 (230 V) |
| Output |
| Output | Controlled, isolated DC voltage |
| Rated voltage Vout DC | 24 V |
| Total tolerance, static ± | 3 % |
| Static mains compensation, approx. | 0.1 % |
| Static load balancing, approx. | 0.1 % |
| Residual ripple peak-peak, max. | 100 mV |
| Residual ripple peak-peak, typ. | 50 mV |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 240 mV |
| Spikes peak-peak, typ. (bandwidth: 20 MHz) | 220 mV |
| Adjustment range | 24 ... 28 V |
| Product function Output voltage adjustable | Yes |
| Output voltage setting | via potentiometer; max. 960 W |
| Status display | Green LED for 24 V OK; LED yellow for overload; LED red for short-circuit or latching shutdown |
| Signaling | Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK" |
| On/off behavior | Overshoot of Vout approx. 3 % |
| Startup delay, max. | 1.5 s |
| Voltage rise, typ. | 30 ms |
| Rated current value Iout rated | 40 A |
| Current range | 0 ... 40 A |
| Note | +60 ... +70 °C: Derating 3%/K |
| Supplied active power typical | 960 W |
| Short-term overload current | |
| on short-circuiting during the start-up typical | 120 A |
| at short-circuit during operation typical | 120 A |
| Duration of overloading capability for excess current | |
| on short-circuiting during the start-up | 25 ms |
| at short-circuit during operation | 25 ms |
| Constant overload current | |
| on short-circuiting during the start-up typical | 60 A |
| Parallel switching for enhanced performance | Yes; switchable characteristic |
| Numbers of parallel switchable units for enhanced performance | 2 |
| Efficiency |
| Efficiency at Vout rated, Iout rated, approx. | 92 % |
| Power loss at Vout rated, Iout rated, approx. | 82 W |
| Power loss [W] during no-load operation maximum | 6.8 W |
| Closed-loop control |
| Dynamic mains compensation (Vin rated ±15 %), max. | 1 % |
| Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. | 1.9 % |
| Load step setting time 50 to 100%, typ. | 2 ms |
| Load step setting time 100 to 50%, typ. | 2 ms |
| Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. | 3.8 % |
| Load step setting time 10 to 90%, typ. | 1 ms |
| Load step setting time 90 to 10%, typ. | 1 ms |
| Setting time maximum | 1 ms |
| Protection and monitoring |
| Output overvoltage protection | < 32 V |
| Current limitation, typ. | 41 A |
| Property of the output Short-circuit proof | Yes |
| Short-circuit protection | Alternatively, constant current characteristic approx. 41 A or latching shutdown |
| Enduring short circuit current RMS value | |
| typical | 41 A |
| Overcurrent overload capability in normal operation | 250% Iout rated up to 25 ms, 150% Iout rated up to 5 s/min |
| Overload/short-circuit indicator | LED yellow for "overload", LED red for "latching shutdown" or "short-circuit" |
| Safety |
| Primary/secondary isolation | Yes |
| Galvanic isolation | Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 |
| Protection class | Class I |
| Leakage current | |
| maximum | 0.1 mA |
| typical | 0.1 mA |
| CE mark | Yes |
| UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1) |
| Explosion protection | IECEx Ex nA nC IIC T3 Gc; ATEX (EX) II 3G Ex nA nC IIC T3; cULus (Hazloc) Class I, Div. 2, Group ABCD, T3; File E330455 |
| FM approval | - |
| CB approval | Yes |
| Marine approval | ABS, DNV GL |
| Degree of protection (EN 60529) | IP20 |
| EMC |
| Emitted interference | EN 55022 Class B |
| Supply harmonics limitation | - |
| Noise immunity | EN 61000-6-2 |
| Operating data |
| Ambient temperature | |
| during operation | -25 ... +70 °C |
| — Note | with natural convection |
| during transport | -40 ... +85 °C |
| during storage | -40 ... +85 °C |
| Humidity class according to EN 60721 | Climate class 3K3, no condensation |
| Mechanics |
| Connection technology | screw-type terminals |
| Connections | |
| Supply input | L, N, PE: 1 screw terminal each for 0.2 ... 4 mm² single-core/finely stranded |
| Output | +, -: 2 screw terminals each for 0.5 ... 10 mm² |
| Auxiliary | 13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm² |
| Width of the enclosure | 145 mm |
| Height of the enclosure | 145 mm |
| Depth of the enclosure | 150 mm |
| Required spacing | |
| top | 40 mm |
| bottom | 40 mm |
| left | 0 mm |
| right | 0 mm |
| Weight, approx. | 3.1 kg |
| Product feature of the enclosure housing for side-by-side mounting | Yes |
| Installation | Snaps onto DIN rail EN 60715 35x15 |
| Electrical accessories | Buffer module, redundancy module |
| Mechanical accessories | Device identification label 20 mm × 7 mm, TI-grey 3RT2900-1SB20 |
| MTBF at 40 °C | 838 156 h |
| Other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) |
| |
